Teradek Bolt 3000 XT 3G-SDI/HDMI Transmitter and Receiver Deluxe Kit (V-Mount)
REQUEST A QUOTE
Description
The Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Transmitter and Receiver Deluxe Kit includes one transmitter and two receivers that have a dual passthrough V-mount plate, as well as a panel antenna, mounting hardware, and a hard-shell protective case. This kit enables you to immediately start transmitting up to 1080p60 video from either an SDI or HDMI source. The zero latency transmitter/receiver pair features 3000′ line-of-sight transmission distance when used together. You can send and receive visually lossless 3G-video signals from a Bolt 3000 transmitter with zero latency. The transmitter features cross conversion, so you take an SDI signal in and loop out either an SDI or HDMI signal to your on-camera monitor.
The receivers also feature both SDI and HDMI outputs, and the system supports digital SD and HD signals. Although the inputs and outputs support a variety of HD signals, in both 50 and 60 Hz standards as well as 480i and 576i. However, 480p and 576p are only supported via HDMI. You can transmit up to three other receiver models such as the Bolt 3000 XT, Sidekick II, or 703 Bolt 703, and the transmitter can support up to four receivers. The built-in AES-128 encryption helps to keep your transmitted video safe from prying eyes.
Also included in the Deluxe Kit is a 5 GHz panel antenna array to enhance and extend your transmission and reducing interference. A mini monitor mount ultra arm, Allen wrench set, and a NATO lock kit from Wooden Camera are also included in the kit. A hard-shell case with custom-cut foam and vinyl zipper bag are included to store and transport the entire kit.
Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Transmitter
With the Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Transmitter you can transmit visually lossless 3G video signals to a Bolt 3000 receiver with zero latency. The Bolt XT is also compatible with the Sidekick II and 703 Bolt. The transmitter unit itself can be secured to a camera or other SDI/HDMI video source via a built-in 1/4″-20 threaded hole, as well as two M3 threaded holes. The included antennas provide a powerful signal that can travel up to 3000′ line-of-sight.
A shoe mount is included for attaching to cameras without 1/4″-20 threads. For convenience, both a standard BNC cable and HDMI cable are included so you can plug in right out of the box. Power can be provided using the integrated 2-pin connector via the included D-Tap power cable. The transmitter supports up to four receivers and built-in AES 128 encryption protects your video from prying eyes, while noise rejection helps keep your video clean even when working around 2.4 and 5.8 GHz signals.
* Backward compatible with Teradek’s universal receivers Sidekick II and 703 Bolt, which can receive Bolt 3000 XT signals up to 300′ away
* HDMI and 3G-SDI inputs, with 3G-SDI loop-through output on transmitter
* SDI ancillary data support for metadata, timecode, and start/stop flags from certain camera manufacturers
* 1/4″-20 and M3 mounting points
Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Receiver with Dual V-Mount Plates
With the Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Receiver you can receive visually lossless 3G-video or HDMI signals from a Bolt 3000 transmitter with zero latency. The receiver unit itself can be secured via built-in 3/8″-16 M3 threaded holes or the built-in NATO rail. It also includes dual pass-through male and female V-mount plates that allow you to mount the receiver on a monitor unit and pass the battery power through.
A light stand adapter is included for mounting on stands. For convenience, a standard HDMI cable is included so you can plug in right out of the box. Power can be provided using the integrated 2-pin connector. A D-Tap power cable is included for attaching to a battery. The receiver can share the transmitter with up to three other receivers. It features built-in AES-128 encryption that protects your video from prying eyes, while noise rejection helps keep your video clean even when working around 2.4 and 5.8 GHz signals.
* The receiver includes built-in cross conversion and Teradek’s proprietary software utilities including a manual frequency selection tool, 3D LUT engine, and a 5 GHz spectrum analyzer to keep an eye on interference in your area.
* The receiver features an HDMI output as well as dual 3G-SDI outputs.
* An integrated NATO rail on the receiver along with several M3 mounting points and an ARRI-compatible 3/8″-16 threaded hole with locating pin holes provide multiple mounting options.
* SDI ancillary data support for metadata, timecode, and start/stop flags from certain camera manufacturers.
* Five included antennas for the receiver enable it to pick signals up with clarity.
Teradek Antenna Array for Bolt 1000/3000 XT Receiver (2nd Generation, Gold Mount)
This Antenna Array from Teradek is a panel antenna with a V-mount, designed to enhance wireless video transmission to Bolt 1000 XT and 3000 XT receivers. This MIMO (Multiple In/Multiple Out) antenna focuses the RF signal and reduces interference, producing a more resilient transmission. It offers a boost in reception but does not increase the maximum transmission range. The panel array is composed of 3 x 16 dBi and 2 x 14 dBi antennas, and operates in the 5.1 to 5.8 GHz frequency range.
* Boosts wireless video transmission
* Focuses wireless signal and reduces interference
* 5.1 to 5.8 GHz frequency range
* Array of 3 x 16 dBi and 2 x 14 dBi antennas
Wooden Camera Ultra Arm Mini Monitor Mount (1/4″-20 to 1/4″-20)
The 1/4″-20 to 1/4″-20 Ultra Arm Mini Monitor Mount from Wooden Camera is a robust and compact articulating arm with 25mm ball joints. Approximately 5″ in length from end to end, the Ultra Arm Mini is designed for keeping a monitor or other accessory close to the camera while providing the full range of ball joint articulation. A lever in the center locks both ball joints, and the mounting points on the ends attach to your gear easily at the turn of integrated tightening knobs. Both ends feature rubber pads for more secure support
The Ultra Arm system is interchangeable. Wooden Camera offers a variety of optional end points that install into the ball sockets of the arm. These include NATO clamps, NATO rails, shoe mounts, super clamps, and extensions to add between two of these arms. There is even a Preston mounting bracket. Additionally, the system is compatible with many third-party 25mm ball mount systems.
Key Features
* Full-range ball joint articulation
* Integrated tightening knobs
* Rubber pads
* Interchangeable end points support optional NATO clamps, NATO rails, shoe mounts, super clamps, length extensions, and more (see Accessories tab)
* Also compatible with third-party 25mm ball mount systems
Wooden Camera NATO Lock Kit
Quickly secure and detach accessories from your camera rig by adding this NATO Lock Kit from Wooden Camera. The rail attaches to your camera or cage system using the included 1/4″-20 or 3/8″-16 screws while the clamp attaches to the accessory itself via an additional set of 1/4″-20 and 3/8″-16 screws. The rail and clamp are compatible with other NATO standard accessories from RED, Zacuto, and other 3rd party manufacturers.
Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Transmitter Specs | |
Transmitter | |
Construction | Milled aluminum (chassis) and regulation-compliant PCB |
Video Inputs | SDI: 1 x BNC (75 Ohm), 3G/HD/SD HDMI: 1 x HDMI type A receptacle |
Video Outputs | SDI: 1 x BNC (75 Ohm), 3G/HD/SD, loop through |
Color Sampling | SDI: YCbCr 4:2:2, 10-bit (8-bit when format conversion is enabled) HDMI: RGB 4:4:4, 8-bit |
Latency | <0.001 seconds (Tx to Rx without format conversion) |
Supported Resolutions | 1080p: 60/59.94/50/30/29.97/25/24/23.98 1080PsF: 30/29.97/25/24/23.98 1080i: 60/59.94/50 720p: 60/59.94/50 480i: 59.94 576i: 50 |
Video Processing | Compression Visually lossless Color Correction CDL/1024 1D LUT (supports 10-bit color) 33x33x33 3D LUT (supports 10-bit color) |
Audio Compression | 48 kHz, 24-bit PCM |
Audio Input | Embedded |
Interfaces | Switches: On/Off and Reset Desktop App: Feature-rich Bolt Manager application for Mac OS X and Windows USB Interface Functionality: Upgrade via mini-USB |
Wireless | Non-DFS Frequencies UA: 5.19 to 5.23 GHz, 5.755 to 5.795 GHz EU & JP: 5.19 to 5.23 GHz DFS Frequencies US: 5.27 to 5.55 GHz and 5.67 GHz EU & JP: 5.27 to 5.67 GHz |
RF Power | 17 dBm EIRP |
Encryption | AES-128 |
Range | Up to 3000' / 914.4 m line of sight |
Unicast Multicast | Unicast / Multicast |
Noise Rejection | Can coexist with WiFi and 5 GHz cordless phones |
Power Input | 2-pin connector 7 to 17 VDC |
Power Consumption | Nominal 7.3 W (measured at 1080p60) |
Operating Temperature | 32 to 104°F / 0 to 40°C |
Mountable | 1 x 1/4"-20 threaded mounting hole 2 x M3 threaded mounting holes |
Dimensions | 0.95 x 2.6 x 4.47" / 2.41 x 6.6 x 11.35 cm |
Weight | 8 oz / 226 g |
Packaging Info | |
Package Weight | 1.66 lb |
Box Dimensions (LxWxH) | 6.7 x 6.6 x 4.8" |
Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Receiver Specs | |
Wireless | |
Wireless Range | 3000' / 914.4 m |
Channel Bandwidth | 40 MHz, 20 MHz |
Frequency Range | Non-DFS Frequencies US, JP, EU: 5.19 to 5.23 GHz US: 5.75 to 5.79 GHz DFS Frequencies US, JP, EU: 5.27 to 5.67 GHz US: 5.27 to 5.55 GHz |
Latency | < 1 ms |
RF Power | 17 dBm |
Wireless Video Compression | Uncompressed |
Interfaces | |
Antenna Ports | 5 x RP-SMA Female |
Video Connectors | 1 x BNC (3G-SDI) Output 1 x HDMI (HDMI 1.4) Output |
Other I/O | 1 x USB Mini-B USB 3.1 Gen 1 Input |
HDCP Support | None |
Embedded Audio | HDMI: 2-Channel SDI: 2-Channel |
Encryption | 128-Bit AES |
Format Support | |
Broadcast System Compatibility | NTSC, PAL |
Video Format | SDI/BNC: 1080p 4:2:2 YCC 8-Bit at 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 fps 1080PsF 4:2:2 YCC 8-Bit at 23.98, 24, 25, 29.97, 30 fps 1080i/720p 4:2:2 YCC 8-Bit at 50, 59.94, 60 fps 576i/480i HDMI: 1080p 4:4:4 RGB 8-Bit at 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 fps 1080PsF 4:4:4 RGB 8-Bit at 23.98, 24, 25, 29.97, 30 fps 1080i/720p 4:4:4 RGB 8-Bit at 50, 59.94, 60 fps 576p at 50 fps 480p at 59.94 fps 576i/480i |
Audio Format | 2-Channel 24-Bit 48 kHz PCM Audio |
Timecode | Yes |
LUT Support | 1024 1D LUT 17x17x17 3D LUT |
Display | |
Panel Type | OLED |
Power | |
Built-In Battery | None |
Battery Support | 1 x V-Mount |
Power Connector | 1 x 2-Pin LEMO (7 to 28 VDC) Input |
Power Consumption | (8.5 W) |
Environmental | |
Operating Temperature | 32 to 104°F / 0 to 40°C |
General | |
Mounting | 1 x M3 Female 1 x 3/8"-16 Female |
Materials | Aluminum, PCB |
Dimensions | 5.43 x 3.5 x 0.94" / 138 x 89 x 24 mm (Without Antennas) |
Weight | 13.26 oz / 376 g (Without Battery Plate) |
Packaging Info | |
Package Weight | 2.45 lb |
Box Dimensions (LxWxH) | 6.7 x 6.5 x 4.8" |
Teradek Antenna Array For Bolt 1000/3000 XT Receiver (2nd Generation, Gold&Nbsp;Mount) Specs | |
Transmitter | |
Compatibility | For Bolt 1000/3000 XT Receiver |
Frequency Range | 5.1 to 5.8 GHz |
Antenna Gain | 3 x 16 dBi 2 x 14 dBi |
Protocol Support | MIMO Standard |
Material of Construction | UV-Protected Plastic, Aluminum Alloy |
Battery Mount | Gold |
Dimensions | Not Specified by Manufacturer |
Weight | Not Specified by Manufacturer |
Packaging Info | |
Package Weight | 8.035 lb |
Box Dimensions (LxWxH) | 17.3 x 17.3 x 4.5" |
Wooden Camera Ultra Arm Mini Monitor Mount (1/4"-20 To 3/8"-16) Specs | |
Top Mount | 3/8"-16 Male |
Bottom Mount | 1/4"-20 Male |
Points of Articulation | 2 |
Maximum Length | 5" / 12.7 cm |
Weight | 4.8 oz / 136 g |
Packaging Info | |
Package Weight | 0.41 lb |
Box Dimensions (LxWxH) | 5.65 x 2.75 x 1.2" |
Wooden Camera NATO Lock Kit Specs | |
Compatibility | RED Swat rails Zacuto Z-rails Other 3rd party NATO products |
Dimensions | 1.9 x 1.9 x 0.7" (47.2 x 47.2 x 18.3 mm) |
Weight | 0.1 lb (50 g) |
Packaging Info | |
Package Weight | 0.13 lb |
Box Dimensions (LxWxH) | 3.2 x 2.7 x 0.85" |
Returns and Exchanges
There are a few important things to keep in mind when returning a product you purchased.You can return unwanted items by post within 7 working days of receipt of your goods.
- You have 14 calendar days to return an item from the date you received it.Â
- Only items that have been purchased directly from Us.
- Please ensure that the item you are returning is repackaged with all elements.
Ship your item back to Us
Firstly Print and return this Returns Form to:
30 South Park Avenue, San Francisco, CA 94108, USA
Please remember to ensure that the item you are returning is repackaged with all elements.
For more information, view our full Returns and Exchanges information.